From the makers of Equipment Maintenance Log — a maintenance log you keep by voice

Daily Equipment Inspection Checklist

November 13, 2026 · 4 min read

A daily equipment inspection is a 5–10 minute walk-around before the shift: fluid levels, leaks, tires or tracks, attachments, safety devices and gauges after start-up. The inspection only pays off if defects are recorded with the machine, the hour reading and a photo, and someone closes them out. A defect that lives only in the operator's head will be there again tomorrow, only bigger.

The pre-shift walk-around

Do it the same way every time: walk around the machine in one direction, top to bottom, then start up and check the cab. Habit is what keeps things from being skipped.

Before start-up

  • Engine oil, coolant, hydraulic oil levels (and transmission oil on loaders and trucks).
  • Fuel level and water drained from the separator if the machine has one.
  • Leaks on the ground and around hoses, cylinders and fittings.
  • Tires: pressure, cuts, missing lug nuts. Tracks: tension, loose shoes, damaged rollers.
  • Bucket, teeth, cutting edges, quick coupler pins locked.
  • Greasing done per the daily chart.
  • Air filter restriction indicator.
  • Steps, handrails and windows clean and intact.
  • Fire extinguisher present and charged.

After start-up

  • Warning lights out, gauges normal.
  • Horn, lights, backup alarm and camera work.
  • Brakes, steering and travel controls respond normally.
  • Hydraulics: no jerky movement or unusual noise.
  • Seat belt and safety interlocks work.

How to rate what you find

Status Meaning Action
OK Nothing found Go to work
Watch Minor issue, safe to run Record it, recheck tomorrow
Fix soon Will get worse, not unsafe yet Record, schedule repair this week
Do not operate Safety or major damage risk Tag out, tell the supervisor, record

A small weeping fitting is "watch." A brake that pulls is "do not operate." When in doubt, the operator should be able to stop the machine without arguing about it.

How to record a defect so it gets fixed

Most defects are noticed. Far fewer are fixed, because the information never reaches the person with the wrench. A useful defect record has:

  • Which machine. Unit name or number.
  • What and where. "Hydraulic hose weeping at the boom cylinder, left side."
  • Hour reading. So you can tell if it is getting worse over time.
  • Photo. Worth a paragraph of description.
  • Status. Open until someone records the repair.

Then close the loop: when the mechanic fixes it, the repair entry references the defect. Open defects should be visible to the owner without asking around.

Daily checks feed into the bigger schedule. For skid steers, the skid steer maintenance checklist adds 50 and 250-hour items, and the excavator maintenance intervals guide covers the service table for excavators.

How to keep it going

In Equipment Maintenance Log, each machine has its own chat, so a defect goes straight into that machine's history. The operator takes a photo and says: "Coolant leak at the lower radiator hose, 3,415 hours, still OK to run." The AI assistant saves it with the date and hours. When the mechanic fixes it, he says "Replaced lower radiator hose, 3,422 hours," and the history shows both. Everyone on the team sees the same log. AI can make mistakes, so entries can be reviewed and corrected. More on logging by voice.

FAQ

Are daily equipment inspections required?

Many safety programs, insurers and customers expect a documented pre-use inspection, and some equipment types have specific rules. Check the requirements for your equipment and work. Either way, a daily check is the cheapest maintenance you can do.

How long should a daily inspection take?

Five to ten minutes for most machines once the routine is a habit. If it takes much longer, the checklist is probably too long for daily use.

Who should do the inspection?

The operator who runs the machine that shift. They know how it felt yesterday and will notice changes first.

Should I record inspections where nothing was found?

A short "walk-around done, no issues" entry with the hours is enough. It shows the machine was checked and gives you a running hour history.

Log your next repair by voice

Free on iPhone and Android. Sign in with Apple, Google or email. Say it — it is logged.