From the makers of Equipment Maintenance Log — a maintenance log you keep by voice
Engine Hours Maintenance Schedule: A Simple Method for Small Fleets
Schedule service by engine hours, not by the calendar, for any machine whose workload changes from month to month. Write down the hour meter reading at every service, add the interval from the operator's manual (typical: oil every 250 hours), and you get the hour reading when the next service is due. Check hours weekly, and you will never be far off.
Why engine hours beat the calendar
A calendar schedule assumes every machine works the same amount. On a contractor fleet that is never true. One excavator runs 50 hours a week on a site prep job while another sits in the yard waiting for the next bid. If both get oil every three months, one is badly overdue and the other gets fresh oil it did not need.
Engine hours measure actual wear. Oil breaks down, filters load up and pins wear in proportion to running time, not days. That is why most equipment manuals list service intervals in hours first and give a calendar limit only as a backstop ("every 250 hours or 6 months, whichever comes first").
Use the calendar for things that age even when a machine sits: coolant, batteries, hydraulic hoses, and annual inspections.
Typical intervals by hours
These are common ranges for diesel construction equipment. Your operator's manual always wins — check it for each model.
| Interval | Typical items |
|---|---|
| Daily / 10 hours | Walk-around, fluid levels, grease pins, check tracks or tires, drain water separator |
| 50 hours | Grease points that need less frequent service, check belts and hoses, first oil change on a new machine (some models) |
| 250 hours | Engine oil and filter, fuel filter check, air filter inspection |
| 500 hours | Fuel filters, hydraulic return filter (many models), final drive oil check |
| 1,000 hours | Hydraulic filters, transmission or swing drive oil, valve check on some engines |
| 2,000 hours | Hydraulic oil, coolant (if not on a calendar limit), major inspection |
A machine that runs 1,200 hours a year will see about five 250-hour services. A generator on standby may run 100 hours a year and should switch to the calendar limit instead.
A simple method for 1–20 machines
You do not need fleet software to start. You need three numbers per machine.
- Current hours. Read the hour meter once a week, same day, every machine.
- Hours at last service. Written down every time the oil is changed or a filter is replaced.
- Next due. Last service hours plus the interval. A skid steer serviced at 2,140 hours on a 250-hour interval is due at 2,390.
Then sort your list by "hours remaining." Anything under 50 hours goes on next week's work list. Anything already past due gets serviced before it goes back out.
A few habits keep this honest:
- Record the hour reading at the moment of service, not from memory later.
- Note what was actually done ("oil and filter, air filter blown out"), not just "service."
- Keep the record with the machine, not on a single office computer one person updates.
- If a machine changes operators or jobsites, the record goes with it.
Where the schedule usually breaks
The math is easy. The data is the hard part. Hours get written on a shop rag, the mechanic forgets to tell the office, or the spreadsheet lives on one laptop. After a few months the "next due" column is a guess.
The fix is to make recording an hour reading take less effort than forgetting it. That means logging it right where the work happens, from a phone, in seconds.
How to keep it going
In Equipment Maintenance Log, each machine has its own chat. After a service, the mechanic says: "Changed oil and filter on the 320, 4,820 hours." The AI assistant turns that into a record with the repair, the hour reading and the date. Weekly readings work the same way: "Skid steer 3, 2,140 hours." Reminders for the next oil change or inspection are based on the hours you log, and the full service history is one tap away. The AI can make mistakes, so every entry can be reviewed and corrected. Questions about setup go to support.
FAQ
Should I use hours or months for maintenance?
Use hours for anything that wears with running time: oil, filters, grease, drivetrain fluids. Use the calendar for things that age while parked, like coolant and batteries. Most manuals say "hours or months, whichever comes first," so track both.
How often should I read the hour meter?
Weekly is enough for most small fleets. Machines running long shifts every day can be read at each fuel-up. The key is a regular reading, not a perfect one.
What if the hour meter is broken?
Estimate hours from shift logs until it is fixed, mark the estimate clearly, and write down both the old and new meter readings when it is replaced. That keeps the history continuous.
Is 250 hours the standard oil change interval?
It is a common interval for diesel equipment, but some engines run 500 hours with the right oil and conditions. Dusty, hot or heavy-load work often calls for shorter intervals. Check your operator's manual.
