From the makers of Equipment Maintenance Log — a maintenance log you keep by voice
Engine Hours vs Miles
There is no exact conversion, but a common rule of thumb is that one engine hour equals roughly 30 to 40 highway miles of wear on a truck. At a 30 mph average, an hour is 30 miles; at 40, it is 40. Engines that idle, run a PTO or crawl in traffic log hours with almost no miles, so hours often tell the truth about wear better than the odometer does.
Why the two numbers disagree
An odometer counts distance. An hour meter counts how long the engine ran, loaded or not. A truck cruising at 60 mph covers 60 miles per engine hour. A concrete pump truck, a bucket truck or a plow truck might cover 3 miles in the same hour while the engine is working the whole time.
That is why a pickup with 60,000 miles that spent years idling on job sites can be more worn than one with 120,000 highway miles. The oil, filters and bearings do not care about distance. They care about how long the engine ran and how hard.
The conversion rule, with the math
Take your average speed over a normal workday, including stops and idle:
| Typical use | Average speed | Miles per engine hour |
|---|---|---|
| Long-haul highway | 50-60 mph | 50-60 |
| Mixed delivery / service route | 20-30 mph | 20-30 |
| Job-site truck, lots of idling | 5-15 mph | 5-15 |
| Bucket / PTO / plow truck | 1-5 mph | 1-5 |
Worked example: a service truck shows 4,200 engine hours and 78,000 miles. That is 78,000 / 4,200 = about 18.6 miles per hour. If you had only the odometer and assumed highway use, you would think of it as a 78,000-mile truck. By the hours, at a 35 miles-per-hour rule it has done the equivalent of roughly 147,000 miles of running. Treat that as a rough comparison, not a measurement.
Which number should drive maintenance?
Use whichever interval comes first. Many engine manufacturers publish service intervals in miles and in hours, often with a note that heavy idling or severe duty shortens them. A commonly used shortcut is to count idle time separately: if a truck idles two hours a day, add that to the hour total even though no miles pass.
For off-road equipment there is no odometer at all, so everything is in hours. The engine hours maintenance schedule shows the typical 250, 500 and 1,000-hour pattern. Always confirm the intervals for your own engine in the owner's or operator's manual.
Buying a used truck: read both numbers
- Divide miles by hours. A very low miles-per-hour figure means heavy idle or PTO use.
- Ask whether the hour meter was ever replaced or reset, and ask for the service records. A voice maintenance log makes those easy to keep.
- Look at service records. A well-documented truck at higher hours often beats a mystery truck at lower hours.
Keeping both numbers in one place
When you log work in Equipment Maintenance Log, you can enter engine hours or mileage by voice or text, for example "Oil change, 4,200 hours, 78,000 miles." The history for each truck then shows both readings over time, and reminders for oil change or inspection can be based on logged hours or miles. AI can make mistakes, so every entry can be reviewed and corrected.
FAQ
How many miles is one engine hour?
It depends on average speed. Highway driving gives 50 to 60 miles per hour; job-site work often gives 5 to 15. The popular 30 to 40 miles figure is only a rough middle for mixed use.
Is an engine hour worth more wear than a mile?
On a per-unit basis, yes, because an hour includes time when the engine runs and moves nothing. A mile is one slice of an hour at speed.
Can I convert hours to miles for resale?
You can estimate for comparison, but buyers and appraisers will still read the actual meters and the records. Keep both readings documented.
Should I put an hour meter on a road truck?
If the truck idles or runs a PTO a lot, it is worth knowing engine hours. Many modern trucks already record them in the engine computer.
