From the makers of Equipment Maintenance Log — a maintenance log you keep by voice

Forklift Daily Inspection Checklist

November 17, 2026 · 4 min read

A forklift should be inspected before every shift by the operator who will drive it, with a visual check first and an operational check after start-up. Cover forks, mast and chains, tires, fluids, leaks, battery or fuel system, brakes, steering, horn, lights, seat belt and hydraulics. If anything affects safety, the truck is tagged out and not driven until it is repaired.

Many workplaces and safety programs expect a documented pre-use check, so confirm the requirements that apply to your site. The list below is a practical starting point, not a replacement for the operator's manual.

Visual check (engine off)

Item What to look for
Forks Cracks, bends, heel wear, loose positioning pins, matched and level tips
Mast and carriage Damage, loose bolts, worn rollers
Lift chains Dry or rusty links, uneven stretch, broken pins, anchor condition
Hoses and cylinders Leaks, wet fittings, cuts, rubbing
Tires Chunking, cuts, flat spots, cord showing; for pneumatics, pressure and lug nuts
Overhead guard and backrest Cracks, missing bolts
Fluids (internal combustion) Engine oil, coolant, hydraulic oil, fuel; radiator clear of debris
Battery (electric) Charge level, cable condition, connector, water level where applicable, no corrosion
LPG (propane) Tank mounted and locked, hose, valve, no smell of gas
Data plate and capacity Present and readable

Operational check (engine running)

  • Gauges and warning lights: normal after start-up.
  • Horn, headlights, work lights, backup alarm, strobe or blue light.
  • Seat belt latches and the seat switch or operator-presence system works.
  • Parking brake holds; service brake pedal firm, not spongy.
  • Steering: no excess play, smooth turning lock to lock.
  • Mast: raise and lower through the full range, then tilt forward and back. Watch for jerking, noise or drift.
  • Attachments and side shift work smoothly.
  • Hydraulics hold the load position without creeping down.

What takes a forklift out of service

Tag the truck and do not drive it if you find any of these:

  1. Brakes weak or the parking brake does not hold.
  2. Steering loose or binding.
  3. Cracked, bent or badly worn forks, or a damaged chain.
  4. Active hydraulic leak or a mast that drifts under load.
  5. Horn, lights or seat belt not working where they are required.
  6. Fuel, LPG or battery fault that is a fire or burn risk.
  7. Missing or illegible capacity plate.

A good rule is that the operator can take a truck out of service without needing permission from a supervisor.

Recording the check so it counts

A paper sheet on a clipboard works until it goes missing. Whatever you use, each record needs the truck number, the date, the hour meter reading, the operator, and a pass or defect line. Defects need a short note and a photo if possible, and they stay open until the repair is logged. Hour readings also tell you when the periodic service is due. The wider daily equipment inspection checklist shows the same pattern for other machines.

Doing it in the app

In Equipment Maintenance Log, each forklift can have its own chat. The operator says "Forklift 3, pre-shift check done, 6,812 hours, left fork tip chipped, photo attached." The AI assistant turns it into a record with the date, hours and the defect, and the photo and notes stay with the truck. Operators, mechanics and managers all see the same log, and entries can be reviewed and corrected if the AI got something wrong. The same habit works with voice logging.

FAQ

How often should a forklift be inspected?

Before each shift, and again if a different operator takes over. Operators on multiple shifts each do their own check.

Does an electric forklift need a different checklist?

Mostly the same, with battery items replacing engine fluids and fuel. Check cables, connectors, charge level and the charging area.

What if the forklift fails the inspection?

Tag it out, report it, record the defect, and keep it out of service until a qualified person repairs it and the repair is documented.

Who keeps the inspection records?

Usually the supervisor or fleet manager. Keep the records where they can be found by truck, not mixed in one binder.

Read next

Log your next repair by voice

Free on iPhone and Android. Sign in with Apple, Google or email. Say it — it is logged.